Lately, I’ve been seeing custom stenciled doormats all over the internet.  But, it seems like the same questions are getting asked over and over.  What did you use for your stencil? What kind of paint did you use? Where did you find your mat?  After reading these questions again and again, I decided to find out the answers myself.
Free SVG cut files for Silhouette & Cricut
There are 3 types of stencil materials I found that others were using: vinyl, freezer paper, and posterboard/cardstock.  I decided to try all three to see which gave the best results.  The end result for all three materials was pretty much the same.  I was able to get nice, clean lines with all of them.
The biggest difference for me was getting the stencil to stay in place on the mat. It is a challenge to get anything to stick to these coir mats.  All three stencil materials required extra work and creativity to get them to stay in place.  In the end,  I decided to do my final design using a vinyl stencil.  Here is my pro/con list for each of the materials.
Freezer Paper
Pros: Inexpensive
Nice clean lines
Cons: Even after ironing at the hottest temperature on my iron, I had a hard time getting the freezer paper to stick.  I had to use pins to keep the small pieces in place.
Can only be cut as big as the mat.
Tricky to transfer from cutting mat to doormat
Vinyl
Pros: Can be cut as long as you need (if you don’t use a mat)
Once I ironed it lightly, I felt it stayed in place the best
Nice clean lines
Cons: You need transfer tape or contact paper to transfer the design to the mat
Most expensive of the three stencil materials
Tricky to transfer from cutting mat to doormat
Cardstock/Posterboard
Pros: Inexpensive
Nice clean lines
Cons: I only had 12″ x 12″ cardstock (not sure if it comes bigger) so I had to piece together the design.  Posterboard comes in bigger sizes, but I feel like it’s harder to get clean cuts and detailed designs.
Tricky to transfer from cutting mat to doormat – I used spray adhesive and pins to keep the stencil from shifting.
In the end, it’s a personal choice of which material works best for you.  If you take the time to make sure your stencil won’t move around and if you use a good painting technique, you will get great results, too.  Now, let’s get onto the tutorial.

This post contains affiliate links

Here is what I used:
– Paint (I used Behr Premium Plus Ultra tinted black)
– Paintbrush (I used a stencil brush)
– Doormat (I used a 18″ x 30″ coir doormat from home depot.  You can also get them at Ikea and Target)
– Vinyl (I used Oracal 631)
– Packing tape of painters tape
Parchment paper or teflon sheet
– Clear Contact Paper (I got mine from the dollar tree)
Clear Polyurethane Spray
– Electronic cutter (cricut explore, silhouette or other cutter)
– Weeding tool
– Cut File (see below)

Here is how I made it:
1. Cut out a vinyl stencil.  I used oracal 631 matte finish.  The matte finish doesn’t stick to the contact paper as well as the oracal 651, which means it also releases from the contact paper much easier. I usually use transfer tape for my vinyl projects, but it was just too sticky.  I picked up some contact paper from the Dollar Tree and it worked perfectly. After the design is cut and weeded, apply the contact paper, and remove the vinyl backing.
2.  Place the vinyl/contact paper over the doormat and measure to be sure the design is centered.  Start to separate the vinyl from the contac paper.  You’re gonna have to hold the vinyl down with your hands because it won’t stick to the mat.  Once you have separated a small section, place a piece of tape along the edge of the vinyl to keep it from moving while you finish removing the contact paper.
3.  Once you have finished removing the contact paper, the vinyl will kind-of just be sitting on the mat.  It could also look like a big mess at this point, just take your time and straighten the design out and put all the pieces where they belong. Another advantage of using 631 is that it’s not as sticky and 651.  If your vinyl gets stuck to itself, it should be pretty easy to pull it apart.
4. Apply heat to help the vinyl stick to the mat. I turned on my iron to the lowest setting, covered the vinyl with parchment paper, and ironed each spot for about one second.  This pulled the vinyl tight and helped it to stick to the mat.  I did this over the entire design until everything looked good.
5. Use a stencil brush and an up and down motion to apply the paint. This should help minimize bleeding. I painted the the design a second time to be sure all areas were covered (not shown in video below)
6.  Once the paint is dry (or until you can’t wait any longer), remove the stencil.
7. Spray on a polyurethane finish for extra protection.
Since this was such a long tutorial, I thought it would be fun to do a time-lapse video of the entire process.  It’s my first video, I hope you enjoy it!
.
Want to make your own?  Download the free cut file below.

In case you’re new here…

I love making digital cutter files and each week I love to share them with you!  This free download will be available through 8/14/17 and is for personal use only. You can purchase the file with a Commercial License from my shop. Here is this week’s freebie. Enjoy!

Free SVG cut files for Silhouette and Cricut

As always, if you have any problems with the files, please let me know. I’ve included .jpg, .png, .svg. .ai, .eps, .dxf, .gsd and .studio in the zip file. Just click to download.

NOTE:  Some computers/browsers are displaying the .svg file with an extension of html or something similar.

Free SVG cut files for Silhouette and Cricut

 Enjoy my free files? I’d really love for you to share this post.  Thanks and come back soon!

22 comments on “DIY Stenciled Doormat and Free SVG File”

  1. wow pretty awesome Im a follower, lol. I like to see someone do something first. I think Im gonna attempt this project this weekend. Thanks for the few file.

  2. Thanks for all the tips and tricks. I have wanted to do a doormat but I am afraid to try. This helps a ton, and I love your file, thanks for sharing!

    • It’s not as scary as it sounds/looks. I hope you decide to try one soon. I already want to make another one for fall.

  3. What an amazing tutorial and file, Angie!!! I wanted to make one of these mats for a wedding shower a month ago but couldn’t because there aren’t any mats in our Home Depot…closest is 90 miles away!!! 🙂 I’ve been trying to convince hubby that we need to go on a day trip 🙂
    P.S. I did find that Target has two in stock; however, a note also said that this product is being discontinued! Where’s Ikea you ask?? 200 miles away!! 🙂

    • Thanks. It was a fun project to make. I kind-of want to do some more:) That’s crazy you are so far from those places. The closest IKEA to me is 17 miles and I think that’s a far drive. I guess I’m kind-of spoiled.

  4. Thank you SO much! Your straightforward directions and video give me confidence that I can do this. Do you know what font you used for “Welcome”? I want to add a name below it and hope to use the same font. Thank you again!

    • Yay! I’m glad you’re going to try it. The font is called Kite. Unfortunately, it’s not a free font, but it is super cute!

  5. Hello, thank you for the tutorial..been wanting to try this. May I ask how big did you cut your Welcome word? thank you

Leave a Reply

Your email address will not be published. Required fields are marked *